Publish Time: 2026-11-15 Origin: Site
A trading company recently contacted us about two suspended truss systems for a studio.
The initial information looked quite clear:
one rectangular truss, approximately 4.5 × 6 m;
one circular truss, approximately 4.5 m in diameter;
both required as complete systems;
suspended from above;
intended for studio use.
Reference photos were also provided.
At first glance, this may seem like enough information for a quotation.
For a simple decorative frame, perhaps it would be.
For a suspended studio truss, it is not.
Before a manufacturer can prepare a useful configuration, we still need to understand two of the most important questions:
How much equipment will the truss carry?
and
Where will that weight be applied?
That is why our next questions were not about price.
They were about:
total loading weight
and
hanging-point arrangement.
When a customer says:
“I need a 4.5 × 6 m rectangular lighting truss.”
we already know something useful.
We know the approximate:
width;
length;
overall geometry.
Likewise, if the request is:
“I need a 4.5 m diameter circular truss,”
we know the required shape and approximate diameter.
But those dimensions do not tell us what the truss actually needs to do.
Two studio trusses can have exactly the same dimensions and still be very different systems.
One may carry only lightweight fixtures.
Another may carry:
many moving-head lights;
LED equipment;
speakers;
scenic elements;
cables;
other production equipment.
So a useful quotation cannot start and finish with overall dimensions.
For standard product families, customers can first review our Lighting Truss range, but a suspended studio configuration still needs project-specific information.
The first missing number we asked for was:
total loading weight
This means the total equipment expected to be carried by the truss.
For a studio project, this may include:
lighting fixtures;
LED equipment;
speakers;
decorative elements;
cabling and accessories;
other suspended production equipment.
The manufacturer does not need this information simply because “more weight means a higher price.”
We need it because the equipment load is part of the structural requirement.
A truss is not selected only according to:
length × width.
It must be considered together with what it will carry.
This is why the same 4.5 × 6 m geometry may lead to a different configuration when the suspended equipment changes.
For customers comparing different standard truss families, our Standard Spigot Truss section provides a useful starting point, but the final selection still depends on the real project load and span.
Suppose the customer answers:
“The total hanging equipment is 800 kg.”
That is much better.
But we are still not finished.
Why?
Because 800 kg evenly distributed around a rectangular truss is not the same as 800 kg concentrated mainly on one side.
This leads to the second question:
Where will the equipment be installed?
In the original conversation, we asked the customer to confirm not only the total load, but also the hanging arrangement.
For the rectangular truss, the most useful information would be something like:
Side A: approximate suspended weight;
Side B: approximate suspended weight;
Side C: approximate suspended weight;
Side D: approximate suspended weight.
That immediately tells the manufacturer much more than one total number.
The same principle applies to a circular truss.
If most fixtures are concentrated in one sector, that is different from a relatively even arrangement around the circle.
This is one of the simplest but most important points in a studio rigging quotation:
The same truss size does not mean the same load condition.
Consider two identical 4.5 × 6 m rectangles.
Lighting is distributed relatively evenly around all four sides.
Most of the moving lights are installed on one 6 m side, with only a few fixtures elsewhere.
The outside dimensions are identical.
The equipment loading is not.
From a manufacturer's point of view, those are not automatically the same quotation problem.
That is why we ask the customer to mark equipment positions whenever possible.
A simple sketch is often enough.
This term can easily create confusion.
When discussing a suspended studio truss, there are actually two different sets of points that matter.
These are the points above the truss where the studio structure allows the truss to be suspended.
We need to know:
how many points are available;
where they are located;
whether their positions are fixed;
whether they correspond to the proposed truss geometry.
These are the positions where the customer intends to attach:
lights;
speakers;
LED equipment;
scenic elements;
other loads.
These two layouts are related, but they are not the same thing.
A useful quotation should try to understand both.
The customer initially sent reference images of suspended studio truss systems.
Those images help us understand the intended appearance.
But a reference image cannot tell us:
what the customer's ceiling can actually support;
where the suspension points exist;
how many hoists will be used;
how the equipment is distributed;
what total load is expected.
So our response was essentially:
Please confirm the total loading weight and the hanging-point arrangement first.
That is not delaying the quotation.
It is preventing us from giving a quotation that looks complete but is based on incomplete assumptions.
Reference photos are very useful during the first conversation.
They tell us whether the customer is thinking about:
rectangular truss;
circular truss;
fixed installation;
lifting system;
studio grid;
suspended lighting frame.
But manufacturers should not copy a photographed structure blindly.
A studio shown in the photo may have:
different ceiling points;
different equipment weights;
different spans;
different hoist positions;
different operating requirements.
So we use photos to understand the concept.
Then we ask for the information needed to prepare the actual configuration.
For customers who want to understand how different layouts influence the overall structure, our Truss Design Configuration page explains the broader relationship between geometry and system layout.
For a suspended studio truss project, the following information makes the quotation process much more efficient:
Information | Why We Need It |
|---|---|
Overall length / width / diameter | Defines the basic truss geometry |
Shape | Rectangular, square, circular or custom |
Intended studio use | Helps us understand the application |
Required working height | Helps define lifting and operating arrangement |
Total equipment weight | Establishes the basic loading requirement |
Equipment distribution | Shows where the main loads occur |
Available ceiling suspension points | Shows where the structure can be supported |
Number / position of lifting points | Helps define lifting arrangement |
Existing hoists or controllers | Avoids quoting equipment the customer already owns |
Studio drawing or ceiling plan | Helps coordinate the complete system |
Reference photos | Helps communicate the desired concept |
Not every customer will have all of this information on the first day.
That is normal.
The important thing is to know which information is still missing.
Customers sometimes think they need to prepare a formal engineering drawing before asking for a quotation.
Usually, that is not necessary at the first stage.
A simple marked drawing can already be very useful.
For a rectangular studio truss, for example:
mark the four sides;
mark the available suspension points;
write the approximate load on each side;
mark any especially heavy fixture groups.
For a circular truss:
mark the main hanging points;
mark where large groups of lights will be installed;
note the approximate total weight.
This gives the manufacturer something practical to work with.
A fast quotation based only on:
“4.5 × 6 m, same as this photo”
may look efficient.
But it often creates more work later.
The customer may then say:
“We need much heavier fixtures.”
“Our ceiling only has four usable points.”
“The hoists must be positioned differently.”
“Most of the equipment is concentrated on one side.”
“We already own the motors.”
“The studio ceiling cannot accept the layout shown in the photo.”
At that point, the original quotation needs to be rebuilt.
So our preference is:
ask the important structural questions before finalizing the quotation.
That usually saves time for both sides.
In this inquiry, the customer said they wanted the complete system.
“Complete system” is useful commercial information.
But it still needs clarification.
A complete suspended truss package might potentially involve:
truss sections;
corners;
circular truss sections;
connectors;
lifting hardware;
hoists;
controllers;
slings or other rigging accessories.
The exact scope depends on what the customer already has and what the studio requires.
Our Truss Accessories section shows many of the component families that may form part of a truss package, but they should not simply be added to every quotation automatically.
The quotation should follow the real system requirement.
For a ground-supported truss, the main support comes from the floor.
For a suspended studio truss, the relationship with the building above becomes part of the project.
That means we need to know what the customer actually has available overhead.
This is especially important because we should not assume:
the number of ceiling points;
their load capacity;
their spacing;
whether they are approved for the intended use.
Those are project-specific conditions.
As a truss manufacturer, we can use the customer's confirmed information to prepare a suitable truss and lifting configuration.
But building suspension points and final rigging verification need to be confirmed for the actual studio.
There is a useful boundary here.
We can prepare a preliminary quotation based on:
dimensions;
intended use;
equipment load;
load distribution;
suspension layout;
lifting requirements.
We can also recommend suitable truss families and component arrangements based on manufacturing experience.
But we should not invent or assume:
building point capacities;
certified ceiling loads;
final rigging approval;
hoist-point adequacy;
structural verification that has not been performed.
For suspended systems, those distinctions matter.
The customer did not provide bad information.
They actually provided the correct first layer:
application;
shape;
dimensions;
reference images.
The problem was simply that a suspended studio truss requires a second layer of information before the quotation becomes meaningful.
That second layer is:
load + distribution + suspension points
This is the part many first-time buyers do not think about.
If you are requesting a suspended studio truss quotation from Dragonstage, the fastest starting package is:
Overall truss dimensions
Required shape
Studio reference drawing or photo
Total equipment load
Approximate equipment positions
Available ceiling suspension-point layout
Required lifting height
What lifting equipment you already own
With those details, we can understand the project much faster and avoid repeatedly revising the quotation.
For broader product options, you can also review our Lighting Truss and Standard Spigot Truss ranges.
For projects that require custom dimensions or non-standard configurations, see Dragonstage Custom Aluminum Stage & Truss Manufacturing.
It is enough for an initial discussion, but usually not enough for a suspended studio system. We also need to understand the equipment load and suspension arrangement.
Because the truss configuration must be considered together with the equipment it will carry, not only its outside dimensions.
Because the same total weight can create different loading conditions depending on whether it is evenly distributed or concentrated in one area.
It can refer to both the available ceiling suspension points and the positions where equipment is installed on the truss. Both may influence the final configuration.
Yes. Reference photos are useful for the first discussion, but additional dimensions, loading information and suspension-point details will normally still be required.
Not necessarily. A simple marked sketch showing dimensions, hanging points and approximate equipment loads is often enough to begin the quotation process.
FOSHAN DRAGON STAGE
No.7,Xiaxi Industrial Area,Heshun,Nanhai District,Foshan,528241,Guangdong,China.
+86 136 3132 8997